Претраживање
Приказ резултата 31-40 од 43
Residual life estimation of a thermal power plant component: The high-pressure turbine housing case
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2009)
This study focuses on the estimation of residual life of damaged thermal power plant components. The high-pressure turbine housing was chosen as an example of thermal power plant component where, during the years of ...
Transport and storage of heavy metals in the Sava River Basin in Serbia
(Srpsko hemijsko društvo, Beograd, 2014)
Selected heavy metals (Cu, Zn, Pb and Cd) in the water and sediment of the Sava River in Serbia were investigated from three locations in the vicinity of industrial and urban settlements (Sabac, Obrenovac and Belgrade) ...
Comparison of refractory coatings based on talc, cordierite, zircon and mullite fillers for lost-foam casting
(Inst Za Kovinske Materiale I In Tehnologie, Ljubjana, 2015)
This study presents the results of an investigation of high-temperature materials refractory coatings based on different refractory fillers including talc, cordierite, zircon and mullite applied in the lost-foam casting ...
Gamma Radiation Absorption Characteristics of Concrete with Components of Different Type Materials
(Polish Acad Sciences Inst Physics, Warsaw, 2010)
Nuclear facilities as nuclear power stations, nuclear research reactors, particle accelerators and linear accelerator in medical institution using concrete in building construction. The different type materials of the ...
Synthesizing a new type of mullite lining
(Inst Za Kovinske Materiale I In Tehnologie, Ljubjana, 2013)
Various possibilities for developing new mullite-based refractory linings that can be applied in a casting process were investigated and are presented in this paper. An optimization of the refractory-lining composition ...
Buckling resistance of stainless steel angle column
(Union of Croatian Civil Engineers and Technicians, 2019)
A numerical study of compressive capacities of stainless steel angle columns is presented in the paper in order to assess the design procedures presented in Eurocode 3. The study focuses on pin-ended hot-rolled equal angle ...
Concrete mix design for reconstruction of northwest breakwater in the Tripoli harbour - Libya
(Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek, 2011)
Reconstruction of Northwest breakwater in the Tripoli Harbour - Libya (about 4500 m long) required manufacture of various concrete elements (cubes and accropodes) in total amount of 550 000 m(3). Volumes of cubes were 6,3 ...
Uticaj geometrije trna alata na mehaničke i strukturne karakteristike sučeonog spoja aluminijumske legure 2024-T351 zavarenog postupkom FSW / Influence of pin geometry on mechanical and structural properties of butt friction stir welded 2024-T351 aluminum alloy
(Savez hemijskih inženjera, Beograd, 2015)
U radu je ispitivano kakav zajednički, kombinovani uticaj brzina rotacije alata, brzina zavarivanja i mala promena u geometriji trna alata imaju na zavarljivost, mehaničke i strukturne karakteristike sučeonog spoja Al ...
Effect of welded joint imperfection on the integrity of pipe elbows subjected to internal pressure
(Faculty of Mechanical Engineering in Slavonski Brod, Faculty of Electrical Engineering in Osijek, Faculty of Civil Engineering in Osijek, 2013)
Since local defects reduce the load-carrying capacity and deformation ability of a piping system, an analysis is undertaken to quantify the influence of weld defects on integrity of the pipe elbows subjected to internal ...
Properties of composite cement with commercial and manufactured metakaolin
(Univ Osijek, Tech Fac, Slavonski Brod, 2013)
Metakaolin composite cements were prepared with 5 to 35 % replacement of ordinary Portland cement with metakaolin (MK), manufactured by thermal activation/calcination of domestic kaolin clay, and commercial matakaolin ...