TY  - JOUR
AU  - Zečević, Bojana
AU  - Milović, Ljubica
AU  - Burzić, Zijah
AU  - Maksimović, Ana
AU  - Aleksić, Vujadin
PY  - 2021
UR  - http://rims.institutims.rs/handle/123456789/403
AB  - Due to its superior strength at high temperatures P/T91 steel is often applied in the chemical, petrochemical and fossil-fired power generation industries. The high strength is achieved by a suitable martensitic microstructure after appropriate heat treatment procedure. Welding is the most important process of joining the components in such plants, and the heat-affected zone is often the weakest part of these structures. Having in mind that the welded joint is the weakest area, it is necessary to know its properties and assess the level of its degradation. It was found that the life-limiting factor in case of P/T91 steel welded structures are the cracks located in the heat affected zones, more precisely in its intercritical region. In present paper the results of the fracture toughness measurement carried out on simulated P91 steel ICHAZ specimens produced using a weld simulator has been presented. The tests were done on two types of simulated specimens, those subjected to the subsequent PWHT and with those left untreated (without PWHT), at room temperature and 600 degrees C. For the J-integral estimation pin-loaded SEN(T) specimens were tested in plane stress conditions using the unloading compliance method of deriving a single specimen resistance curve and the eta-method.
PB  - Springer, New York
T2  - Experimental Techniques
T1  - J-integral Analysis of the Simulated Heat-affected Zone of the Elevated-temperature Martensitic Steel
DO  - 10.1007/s40799-021-00487-9
ER  - 

@article{
author = "Zečević, Bojana and Milović, Ljubica and Burzić, Zijah and Maksimović, Ana and Aleksić, Vujadin",
year = "2021",
abstract = "Due to its superior strength at high temperatures P/T91 steel is often applied in the chemical, petrochemical and fossil-fired power generation industries. The high strength is achieved by a suitable martensitic microstructure after appropriate heat treatment procedure. Welding is the most important process of joining the components in such plants, and the heat-affected zone is often the weakest part of these structures. Having in mind that the welded joint is the weakest area, it is necessary to know its properties and assess the level of its degradation. It was found that the life-limiting factor in case of P/T91 steel welded structures are the cracks located in the heat affected zones, more precisely in its intercritical region. In present paper the results of the fracture toughness measurement carried out on simulated P91 steel ICHAZ specimens produced using a weld simulator has been presented. The tests were done on two types of simulated specimens, those subjected to the subsequent PWHT and with those left untreated (without PWHT), at room temperature and 600 degrees C. For the J-integral estimation pin-loaded SEN(T) specimens were tested in plane stress conditions using the unloading compliance method of deriving a single specimen resistance curve and the eta-method.",
publisher = "Springer, New York",
journal = "Experimental Techniques",
title = "J-integral Analysis of the Simulated Heat-affected Zone of the Elevated-temperature Martensitic Steel",
doi = "10.1007/s40799-021-00487-9"
}

Zečević, B., Milović, L., Burzić, Z., Maksimović, A.,& Aleksić, V.. (2021). J-integral Analysis of the Simulated Heat-affected Zone of the Elevated-temperature Martensitic Steel. in Experimental Techniques
Springer, New York..
https://doi.org/10.1007/s40799-021-00487-9

Zečević B, Milović L, Burzić Z, Maksimović A, Aleksić V. J-integral Analysis of the Simulated Heat-affected Zone of the Elevated-temperature Martensitic Steel. in Experimental Techniques. 2021;.
doi:10.1007/s40799-021-00487-9 .

Zečević, Bojana, Milović, Ljubica, Burzić, Zijah, Maksimović, Ana, Aleksić, Vujadin, "J-integral Analysis of the Simulated Heat-affected Zone of the Elevated-temperature Martensitic Steel" in Experimental Techniques (2021),
https://doi.org/10.1007/s40799-021-00487-9 . .

TY  - JOUR
AU  - Burzić, Zijah
AU  - Burzić, Meri
AU  - Grabulov, Vencislav
AU  - Perković, Srđa
PY  - 2018
UR  - http://rims.institutims.rs/handle/123456789/328
AB  - Primena čelika visoke čvrstoće kod projektovanja zavarenih konstrukcija zahteva podatke o svojstvima istih pri različitim uslovima opterećenja. Zahvaljujući visokom naponu tečenja debljina zida može se smanjiti u poređenju sa opštim konstrukcijskim čelicima, a shodno tome, dimenzije zavarenog spoja, potrošnja dodatnog materijala za zavarivanje i vreme za izradu zavarenih spojeva će biti minimizirani. Ovo je od značaja za opremu pod pritiskom, ali i za druge industrijske grane (kranove, bagere). Kompletna karakterizacija zavarenog spoja mora uključiti podatke za osnovni metal, ali takođe su neophodne osobine metala šava i zone uticaja toplote (ZUT), bar da bi ih uporedili sa svojstvima osnovnog metala. Ovo je od posebnog značaja zbog heterogenosti strukture u ZUT-u. .
AB  - The application of high strength steels in design of heavy duty welded structures requires data about properties in different loading conditions. Thanks to high yield stress the wall thickness can be reduced compared to mild structural steels, and accordingly welded joint cross-sections, welding consumables consumption and time for welded joints manufacturing will be minimized. This is of importance for pressurized equipment, but also for other industrial branches (cranes, excavator). Complete characterization of welded joint has to include data for parent metal, but also the properties for weld metal and the heat-affected-zone (HAZ) are necessary, at least in order to compare them with parent metal properties. This is of special importance because of heterogeneity structure in HAZ.
PB  - Vojnotehnički institut, Beograd
T2  - Scientific Technical Review
T1  - Uticaj prsline na karakteristike zavarenog spoja pri različitim vrstama opterećenja
T1  - Influence of crack on welded joint characteristics in different types of loads
EP  - 58
IS  - 1
SP  - 50
VL  - 68
DO  - 10.5937/str1801050B
ER  - 

@article{
author = "Burzić, Zijah and Burzić, Meri and Grabulov, Vencislav and Perković, Srđa",
year = "2018",
abstract = "Primena čelika visoke čvrstoće kod projektovanja zavarenih konstrukcija zahteva podatke o svojstvima istih pri različitim uslovima opterećenja. Zahvaljujući visokom naponu tečenja debljina zida može se smanjiti u poređenju sa opštim konstrukcijskim čelicima, a shodno tome, dimenzije zavarenog spoja, potrošnja dodatnog materijala za zavarivanje i vreme za izradu zavarenih spojeva će biti minimizirani. Ovo je od značaja za opremu pod pritiskom, ali i za druge industrijske grane (kranove, bagere). Kompletna karakterizacija zavarenog spoja mora uključiti podatke za osnovni metal, ali takođe su neophodne osobine metala šava i zone uticaja toplote (ZUT), bar da bi ih uporedili sa svojstvima osnovnog metala. Ovo je od posebnog značaja zbog heterogenosti strukture u ZUT-u. ., The application of high strength steels in design of heavy duty welded structures requires data about properties in different loading conditions. Thanks to high yield stress the wall thickness can be reduced compared to mild structural steels, and accordingly welded joint cross-sections, welding consumables consumption and time for welded joints manufacturing will be minimized. This is of importance for pressurized equipment, but also for other industrial branches (cranes, excavator). Complete characterization of welded joint has to include data for parent metal, but also the properties for weld metal and the heat-affected-zone (HAZ) are necessary, at least in order to compare them with parent metal properties. This is of special importance because of heterogeneity structure in HAZ.",
publisher = "Vojnotehnički institut, Beograd",
journal = "Scientific Technical Review",
title = "Uticaj prsline na karakteristike zavarenog spoja pri različitim vrstama opterećenja, Influence of crack on welded joint characteristics in different types of loads",
pages = "58-50",
number = "1",
volume = "68",
doi = "10.5937/str1801050B"
}

Burzić, Z., Burzić, M., Grabulov, V.,& Perković, S.. (2018). Uticaj prsline na karakteristike zavarenog spoja pri različitim vrstama opterećenja. in Scientific Technical Review
Vojnotehnički institut, Beograd., 68(1), 50-58.
https://doi.org/10.5937/str1801050B

Burzić Z, Burzić M, Grabulov V, Perković S. Uticaj prsline na karakteristike zavarenog spoja pri različitim vrstama opterećenja. in Scientific Technical Review. 2018;68(1):50-58.
doi:10.5937/str1801050B .

Burzić, Zijah, Burzić, Meri, Grabulov, Vencislav, Perković, Srđa, "Uticaj prsline na karakteristike zavarenog spoja pri različitim vrstama opterećenja" in Scientific Technical Review, 68, no. 1 (2018):50-58,
https://doi.org/10.5937/str1801050B . .

TY  - JOUR
AU  - Aleksić, Vujadin
AU  - Milović, Ljubica
AU  - Aleksić, Bojana
AU  - Bulatović, Srđan
AU  - Burzić, Zijah
AU  - Hemer, Abubkr
PY  - 2017
UR  - http://rims.institutims.rs/handle/123456789/308
AB  - Experimental research on the behaviour of high-strength low-alloy steel ( HSLA)exposed to low-cycle fatigue (LCF) with controlled and fully reversible strain (Delta epsilon/2 = const, R epsilon =epsilon(min)/epsilon(max) = -1) has been analysed. LCF tests are performed on a series of smooth bar shaped specimens, 11 x 11 x 95 mm, parent metal (PM), welded joint (WJ) and simulated heat affected zone (SHAZ) of steel Nionikral 70 (NN-70) with semi-amplitude of controlled strain, Delta epsilon/2 = 0.40- 0.80. The results of the experimental investigation have given us important information on the understanding of fatigue behaviour of steel NN-70 and its welded joints. In this work the results of static and dynamic-, that is monotonous and fatigue behaviour of the material, are compared, which is a practical contribution to the assessment of the behaviour of PM and WJ of steel NN-70 exposed to effects of low cycle fatigue, i.e. monotonous and fatigue behaviour of the material.
PB  - Institut za ispitivanje materijala, Beograd
T2  - Structural Integrity and Life
T1  - Behaviour of nionikral-70 in low-cycle fatigue
EP  - 73
IS  - 1
SP  - 61
VL  - 17
UR  - https://hdl.handle.net/21.15107/rcub_technorep_3495
ER  - 

@article{
author = "Aleksić, Vujadin and Milović, Ljubica and Aleksić, Bojana and Bulatović, Srđan and Burzić, Zijah and Hemer, Abubkr",
year = "2017",
abstract = "Experimental research on the behaviour of high-strength low-alloy steel ( HSLA)exposed to low-cycle fatigue (LCF) with controlled and fully reversible strain (Delta epsilon/2 = const, R epsilon =epsilon(min)/epsilon(max) = -1) has been analysed. LCF tests are performed on a series of smooth bar shaped specimens, 11 x 11 x 95 mm, parent metal (PM), welded joint (WJ) and simulated heat affected zone (SHAZ) of steel Nionikral 70 (NN-70) with semi-amplitude of controlled strain, Delta epsilon/2 = 0.40- 0.80. The results of the experimental investigation have given us important information on the understanding of fatigue behaviour of steel NN-70 and its welded joints. In this work the results of static and dynamic-, that is monotonous and fatigue behaviour of the material, are compared, which is a practical contribution to the assessment of the behaviour of PM and WJ of steel NN-70 exposed to effects of low cycle fatigue, i.e. monotonous and fatigue behaviour of the material.",
publisher = "Institut za ispitivanje materijala, Beograd",
journal = "Structural Integrity and Life",
title = "Behaviour of nionikral-70 in low-cycle fatigue",
pages = "73-61",
number = "1",
volume = "17",
url = "https://hdl.handle.net/21.15107/rcub_technorep_3495"
}

Aleksić, V., Milović, L., Aleksić, B., Bulatović, S., Burzić, Z.,& Hemer, A.. (2017). Behaviour of nionikral-70 in low-cycle fatigue. in Structural Integrity and Life
Institut za ispitivanje materijala, Beograd., 17(1), 61-73.
https://hdl.handle.net/21.15107/rcub_technorep_3495

Aleksić V, Milović L, Aleksić B, Bulatović S, Burzić Z, Hemer A. Behaviour of nionikral-70 in low-cycle fatigue. in Structural Integrity and Life. 2017;17(1):61-73.
https://hdl.handle.net/21.15107/rcub_technorep_3495 .

Aleksić, Vujadin, Milović, Ljubica, Aleksić, Bojana, Bulatović, Srđan, Burzić, Zijah, Hemer, Abubkr, "Behaviour of nionikral-70 in low-cycle fatigue" in Structural Integrity and Life, 17, no. 1 (2017):61-73,
https://hdl.handle.net/21.15107/rcub_technorep_3495 .

TY  - CONF
AU  - Milović, Ljubica
AU  - Bulatović, Srđan
AU  - Aleksić, Vujadin
AU  - Burzić, Zijah
PY  - 2014
UR  - http://rims.institutims.rs/handle/123456789/232
AB  - A quenched and tempered high strength low alloy steel NIONIKRAL 70 for producing welded pressure vessels, where high resistance to fatigue crack propagation and high tolerance of damage are of high importance, has been investigated. Low cycle fatigue tests were conducting on several series of uniaxial cylindrical smooth specimens under strain control. The cycle behavior of the material is characterized using Coffin-Manson relation.
PB  - Elsevier Science Bv, Amsterdam
C3  - 20th European Conference on Fracture
T1  - Low cycle fatigue of weldments produced of a high strength low alloyed steel
EP  - 1434
SP  - 1429
VL  - 3
DO  - 10.1016/j.mspro.2014.06.231
ER  - 

@conference{
author = "Milović, Ljubica and Bulatović, Srđan and Aleksić, Vujadin and Burzić, Zijah",
year = "2014",
abstract = "A quenched and tempered high strength low alloy steel NIONIKRAL 70 for producing welded pressure vessels, where high resistance to fatigue crack propagation and high tolerance of damage are of high importance, has been investigated. Low cycle fatigue tests were conducting on several series of uniaxial cylindrical smooth specimens under strain control. The cycle behavior of the material is characterized using Coffin-Manson relation.",
publisher = "Elsevier Science Bv, Amsterdam",
journal = "20th European Conference on Fracture",
title = "Low cycle fatigue of weldments produced of a high strength low alloyed steel",
pages = "1434-1429",
volume = "3",
doi = "10.1016/j.mspro.2014.06.231"
}

Milović, L., Bulatović, S., Aleksić, V.,& Burzić, Z.. (2014). Low cycle fatigue of weldments produced of a high strength low alloyed steel. in 20th European Conference on Fracture
Elsevier Science Bv, Amsterdam., 3, 1429-1434.
https://doi.org/10.1016/j.mspro.2014.06.231

Milović L, Bulatović S, Aleksić V, Burzić Z. Low cycle fatigue of weldments produced of a high strength low alloyed steel. in 20th European Conference on Fracture. 2014;3:1429-1434.
doi:10.1016/j.mspro.2014.06.231 .

Milović, Ljubica, Bulatović, Srđan, Aleksić, Vujadin, Burzić, Zijah, "Low cycle fatigue of weldments produced of a high strength low alloyed steel" in 20th European Conference on Fracture, 3 (2014):1429-1434,
https://doi.org/10.1016/j.mspro.2014.06.231 . .

TY  - JOUR
AU  - Bulatović, Srđan
AU  - Burzić, Zijah
AU  - Aleksić, Vujadin
AU  - Sedmak, Aleksandar
AU  - Milović, Ljubica
PY  - 2014
UR  - http://rims.institutims.rs/handle/123456789/229
AB  - High strength low-alloy steel under low cycle fatigue at a certain level of strain controlled achieve stabilized condition. During the fatigue loading stabilized hysteresis loop is determined, which typical cycle of stabilization is calculated as half number of cycles to failure. Stabilized hysteresis loop is a representative of all hysteresis and it's used to determine all of the parameters for the assessment of low cycle fatigue. This paper Shows comparison of complete strain-life curves of low cycle fatigue for two chosen stabilized hysteresis loop cycles of base metal HSLA steel marked as Nionikral 70.
PB  - Croatian Metallurgical Soc, Zagreb
T2  - Metalurgija
T1  - Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue
EP  - 480
IS  - 4
SP  - 477
VL  - 53
UR  - https://hdl.handle.net/21.15107/rcub_technorep_2811
ER  - 

@article{
author = "Bulatović, Srđan and Burzić, Zijah and Aleksić, Vujadin and Sedmak, Aleksandar and Milović, Ljubica",
year = "2014",
abstract = "High strength low-alloy steel under low cycle fatigue at a certain level of strain controlled achieve stabilized condition. During the fatigue loading stabilized hysteresis loop is determined, which typical cycle of stabilization is calculated as half number of cycles to failure. Stabilized hysteresis loop is a representative of all hysteresis and it's used to determine all of the parameters for the assessment of low cycle fatigue. This paper Shows comparison of complete strain-life curves of low cycle fatigue for two chosen stabilized hysteresis loop cycles of base metal HSLA steel marked as Nionikral 70.",
publisher = "Croatian Metallurgical Soc, Zagreb",
journal = "Metalurgija",
title = "Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue",
pages = "480-477",
number = "4",
volume = "53",
url = "https://hdl.handle.net/21.15107/rcub_technorep_2811"
}

Bulatović, S., Burzić, Z., Aleksić, V., Sedmak, A.,& Milović, L.. (2014). Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue. in Metalurgija
Croatian Metallurgical Soc, Zagreb., 53(4), 477-480.
https://hdl.handle.net/21.15107/rcub_technorep_2811

Bulatović S, Burzić Z, Aleksić V, Sedmak A, Milović L. Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue. in Metalurgija. 2014;53(4):477-480.
https://hdl.handle.net/21.15107/rcub_technorep_2811 .

Bulatović, Srđan, Burzić, Zijah, Aleksić, Vujadin, Sedmak, Aleksandar, Milović, Ljubica, "Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue" in Metalurgija, 53, no. 4 (2014):477-480,
https://hdl.handle.net/21.15107/rcub_technorep_2811 .

TY  - JOUR
AU  - Popović, Olivera
AU  - Prokić-Cvetković, Radica
AU  - Sedmak, Aleksandar
AU  - Grabulov, Vencislav
AU  - Burzić, Zijah
AU  - Rakin, Marko
PY  - 2010
UR  - http://rims.institutims.rs/handle/123456789/123
AB  - In this paper microstructural and mechanical properties of high-carbon steel surface welded layer, obtained with self-shielded flux cored wire, are presented in the case of a standard rails and crossings. The testing results of tensile characteristics, hardness, toughness via instrumented Charpy pendulum, microstructural analysis and fatigue crack growth resistance of all characteristical zones are analysed in details, especially from the point of view of interaction between microstructure and properties. Obtained results indicate superior properties of repaired welded layers, due to their similarity to the new generation of bainitic steel, i.e., due to change of microstructure from original pearlitic structure to final bainitic structure. Finally, fatigue crack growth parameters have shown that deposite layer has higher resistance to the crack growth, improving overall reliability of rails and crossings.
T2  - Strojniski Vestnik/Journal of Mechanical Engineering
T1  - Characterisation of high-carbon steel surface welded layer
IS  - 5
VL  - 56
UR  - https://hdl.handle.net/21.15107/rcub_rims_123
ER  - 

@article{
author = "Popović, Olivera and Prokić-Cvetković, Radica and Sedmak, Aleksandar and Grabulov, Vencislav and Burzić, Zijah and Rakin, Marko",
year = "2010",
abstract = "In this paper microstructural and mechanical properties of high-carbon steel surface welded layer, obtained with self-shielded flux cored wire, are presented in the case of a standard rails and crossings. The testing results of tensile characteristics, hardness, toughness via instrumented Charpy pendulum, microstructural analysis and fatigue crack growth resistance of all characteristical zones are analysed in details, especially from the point of view of interaction between microstructure and properties. Obtained results indicate superior properties of repaired welded layers, due to their similarity to the new generation of bainitic steel, i.e., due to change of microstructure from original pearlitic structure to final bainitic structure. Finally, fatigue crack growth parameters have shown that deposite layer has higher resistance to the crack growth, improving overall reliability of rails and crossings.",
journal = "Strojniski Vestnik/Journal of Mechanical Engineering",
title = "Characterisation of high-carbon steel surface welded layer",
number = "5",
volume = "56",
url = "https://hdl.handle.net/21.15107/rcub_rims_123"
}

Popović, O., Prokić-Cvetković, R., Sedmak, A., Grabulov, V., Burzić, Z.,& Rakin, M.. (2010). Characterisation of high-carbon steel surface welded layer. in Strojniski Vestnik/Journal of Mechanical Engineering, 56(5).
https://hdl.handle.net/21.15107/rcub_rims_123

Popović O, Prokić-Cvetković R, Sedmak A, Grabulov V, Burzić Z, Rakin M. Characterisation of high-carbon steel surface welded layer. in Strojniski Vestnik/Journal of Mechanical Engineering. 2010;56(5).
https://hdl.handle.net/21.15107/rcub_rims_123 .

Popović, Olivera, Prokić-Cvetković, Radica, Sedmak, Aleksandar, Grabulov, Vencislav, Burzić, Zijah, Rakin, Marko, "Characterisation of high-carbon steel surface welded layer" in Strojniski Vestnik/Journal of Mechanical Engineering, 56, no. 5 (2010),
https://hdl.handle.net/21.15107/rcub_rims_123 .

TY  - CONF
AU  - Sedmak, Stojan
AU  - Gerić, Katarina
AU  - Burzić, Zijah
AU  - Grabulov, Vencislav
AU  - Jovičić, Radomir
PY  - 2009
UR  - http://rims.institutims.rs/handle/123456789/98
AB  - Quality and structural integrity of welded pressure equipment are defined by The Pressure Equipment Directive (97/23/EC). The problem is complex, due to welded joint imperfections, matching effect, heterogeneity of microstructure and material properties. Equipment can be fit for service with defects unacceptable by codes, what should be proved by fracture mechanics approach, especially for cracks in the heat-affected-zone.
PB  - Springer, Dordrecht
C3  - Security and Reliability of Damaged Structures and Defective Materials
T1  - Welded joints behaviour in service with special reference to pressure equipment
EP  - +
SP  - 231
DO  - 10.1007/978-90-481-2792-4_10
ER  - 

@conference{
author = "Sedmak, Stojan and Gerić, Katarina and Burzić, Zijah and Grabulov, Vencislav and Jovičić, Radomir",
year = "2009",
abstract = "Quality and structural integrity of welded pressure equipment are defined by The Pressure Equipment Directive (97/23/EC). The problem is complex, due to welded joint imperfections, matching effect, heterogeneity of microstructure and material properties. Equipment can be fit for service with defects unacceptable by codes, what should be proved by fracture mechanics approach, especially for cracks in the heat-affected-zone.",
publisher = "Springer, Dordrecht",
journal = "Security and Reliability of Damaged Structures and Defective Materials",
title = "Welded joints behaviour in service with special reference to pressure equipment",
pages = "+-231",
doi = "10.1007/978-90-481-2792-4_10"
}

Sedmak, S., Gerić, K., Burzić, Z., Grabulov, V.,& Jovičić, R.. (2009). Welded joints behaviour in service with special reference to pressure equipment. in Security and Reliability of Damaged Structures and Defective Materials
Springer, Dordrecht., 231-+.
https://doi.org/10.1007/978-90-481-2792-4_10

Sedmak S, Gerić K, Burzić Z, Grabulov V, Jovičić R. Welded joints behaviour in service with special reference to pressure equipment. in Security and Reliability of Damaged Structures and Defective Materials. 2009;:231-+.
doi:10.1007/978-90-481-2792-4_10 .

Sedmak, Stojan, Gerić, Katarina, Burzić, Zijah, Grabulov, Vencislav, Jovičić, Radomir, "Welded joints behaviour in service with special reference to pressure equipment" in Security and Reliability of Damaged Structures and Defective Materials (2009):231-+,
https://doi.org/10.1007/978-90-481-2792-4_10 . .

TY  - JOUR
AU  - Zrilić, Milorad
AU  - Grabulov, Vencislav
AU  - Burzić, Zijah
AU  - Arsić, Miodrag
AU  - Sedmak, S.
PY  - 2007
UR  - http://rims.institutims.rs/handle/123456789/58
AB  - in order to gain the benefits of weldable high-strength steels in pressurized equipment applications, satisfactory toughness and crack properties of the welded joint, both in the weld metal and the heat-affected-zone (HAZ), are required. Experimental investigations of toughness and crack resistance parameters through static and impact tests of a high-strength, low-alloy steel (HSLA) with a nominal yield strength of 700MPa and its welded joint, were performed on Charpy-sized specimens, V-notched and pre-cracked, of the parent metal, weld metal and HAZ. The selected electrode produced slight undermatching and enabled the welded joints to be manufactured without cold cracks. The impact energy and its parts responsible for crack initiation and propagation were determined by toughness evaluation. Crack sensitivity, defined as the ratio of the impact energy for V-notched and for pre-cracked specimens, enabled a comparison of the homogeneous microstructure of the parent metal and the weld metal, and of the heterogeneous microstructure of the heat-affected-zone (HAZ), which indicated a better crack toughness behaviour of the HAZ. The results obtained showed that the toughness and crack resistance of the weld metal were significantly lower than those of the parent metal and the HAZ. The fracture mechanics parameters, J(Ic), integral, and plane strain fracture toughness, K-Ic, as well as J resistance curves expressed the degradation less.
PB  - Elsevier Sci Ltd, Oxford
T2  - International Journal of Pressure Vessels and Piping
T1  - Static and impact crack properties of a high-strength steel welded joint
EP  - 150
IS  - 3
SP  - 139
VL  - 84
DO  - 10.1016/j.ijpvp.2006.09.021
ER  - 

@article{
author = "Zrilić, Milorad and Grabulov, Vencislav and Burzić, Zijah and Arsić, Miodrag and Sedmak, S.",
year = "2007",
abstract = "in order to gain the benefits of weldable high-strength steels in pressurized equipment applications, satisfactory toughness and crack properties of the welded joint, both in the weld metal and the heat-affected-zone (HAZ), are required. Experimental investigations of toughness and crack resistance parameters through static and impact tests of a high-strength, low-alloy steel (HSLA) with a nominal yield strength of 700MPa and its welded joint, were performed on Charpy-sized specimens, V-notched and pre-cracked, of the parent metal, weld metal and HAZ. The selected electrode produced slight undermatching and enabled the welded joints to be manufactured without cold cracks. The impact energy and its parts responsible for crack initiation and propagation were determined by toughness evaluation. Crack sensitivity, defined as the ratio of the impact energy for V-notched and for pre-cracked specimens, enabled a comparison of the homogeneous microstructure of the parent metal and the weld metal, and of the heterogeneous microstructure of the heat-affected-zone (HAZ), which indicated a better crack toughness behaviour of the HAZ. The results obtained showed that the toughness and crack resistance of the weld metal were significantly lower than those of the parent metal and the HAZ. The fracture mechanics parameters, J(Ic), integral, and plane strain fracture toughness, K-Ic, as well as J resistance curves expressed the degradation less.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "International Journal of Pressure Vessels and Piping",
title = "Static and impact crack properties of a high-strength steel welded joint",
pages = "150-139",
number = "3",
volume = "84",
doi = "10.1016/j.ijpvp.2006.09.021"
}

Zrilić, M., Grabulov, V., Burzić, Z., Arsić, M.,& Sedmak, S.. (2007). Static and impact crack properties of a high-strength steel welded joint. in International Journal of Pressure Vessels and Piping
Elsevier Sci Ltd, Oxford., 84(3), 139-150.
https://doi.org/10.1016/j.ijpvp.2006.09.021

Zrilić M, Grabulov V, Burzić Z, Arsić M, Sedmak S. Static and impact crack properties of a high-strength steel welded joint. in International Journal of Pressure Vessels and Piping. 2007;84(3):139-150.
doi:10.1016/j.ijpvp.2006.09.021 .

Zrilić, Milorad, Grabulov, Vencislav, Burzić, Zijah, Arsić, Miodrag, Sedmak, S., "Static and impact crack properties of a high-strength steel welded joint" in International Journal of Pressure Vessels and Piping, 84, no. 3 (2007):139-150,
https://doi.org/10.1016/j.ijpvp.2006.09.021 . .

TY  - CONF
AU  - Arsić, Miodrag
AU  - Šarkočević, Živče
AU  - Aleksić, Vujadin
AU  - Burzić, Zijah
PY  - 2003
UR  - http://rims.institutims.rs/handle/123456789/826
C3  - VI Međunarodno savjetovanje o dostignućima elektro i mašinske industrije DEMI 2003, Zbornik
T1  - Uticaj unete količine toplote pri zavarivanju na žilavost metala šava cevi izrađenih od čelika povišene čvrstoće
EP  - 164
SP  - 159
UR  - https://hdl.handle.net/21.15107/rcub_rims_826
ER  - 

@conference{
author = "Arsić, Miodrag and Šarkočević, Živče and Aleksić, Vujadin and Burzić, Zijah",
year = "2003",
journal = "VI Međunarodno savjetovanje o dostignućima elektro i mašinske industrije DEMI 2003, Zbornik",
title = "Uticaj unete količine toplote pri zavarivanju na žilavost metala šava cevi izrađenih od čelika povišene čvrstoće",
pages = "164-159",
url = "https://hdl.handle.net/21.15107/rcub_rims_826"
}

Arsić, M., Šarkočević, Ž., Aleksić, V.,& Burzić, Z.. (2003). Uticaj unete količine toplote pri zavarivanju na žilavost metala šava cevi izrađenih od čelika povišene čvrstoće. in VI Međunarodno savjetovanje o dostignućima elektro i mašinske industrije DEMI 2003, Zbornik, 159-164.
https://hdl.handle.net/21.15107/rcub_rims_826

Arsić M, Šarkočević Ž, Aleksić V, Burzić Z. Uticaj unete količine toplote pri zavarivanju na žilavost metala šava cevi izrađenih od čelika povišene čvrstoće. in VI Međunarodno savjetovanje o dostignućima elektro i mašinske industrije DEMI 2003, Zbornik. 2003;:159-164.
https://hdl.handle.net/21.15107/rcub_rims_826 .

Arsić, Miodrag, Šarkočević, Živče, Aleksić, Vujadin, Burzić, Zijah, "Uticaj unete količine toplote pri zavarivanju na žilavost metala šava cevi izrađenih od čelika povišene čvrstoće" in VI Međunarodno savjetovanje o dostignućima elektro i mašinske industrije DEMI 2003, Zbornik (2003):159-164,
https://hdl.handle.net/21.15107/rcub_rims_826 .

TY  - JOUR
AU  - Burzić, Meri
AU  - Sedmak, Stojan
AU  - Burzić, Zijah
AU  - Zrilić, Milorad
AU  - Jaković, Dragan
AU  - Momčilović, Dejan
PY  - 2003
UR  - http://rims.institutims.rs/handle/123456789/30
AB  - U ovom radu su prikazane metode za određivanje dinamičke žilavosti loma, KId Metode dinamičkog J integrala, i ekvivalenta energije su eksperimentalno potvrđene ispitivanjem čelika Č 5432 i Č 4734. Ovaj rad predstavlja doprinos u ovladavanju metodama koje definišu ponašanje materijala u dinamičkim uslovima rasta prsline. Primena ovih metoda zajedno sa ostalim metodama za određivanje parametara mehanike loma predstavlja značajan doprinos istraživanju ponašanja konstrukcijskih materijala u prisustvu prsline.
AB  - In this paper the investigation of methods for determination of dynamic fracture toughness, KId. Dynamic J-integral and equivalence energy methods are experimental confirm testing of steel Č 5432 and Č 4734. This paper presented of contribution in control methods what's to define behavior of materials in condition of dynamic crack growth. Application this all methods presented very imported contribution of investigation behavior construction materials in presence of crack.
PB  - Visoka tehnička škola strukovnih studija, Beograd
T2  - Tehnička dijagnostika
T1  - Eksperimentalno određivanje dinamičke žilavosti loma KId, kod metalnih materijala visoke čvrstoće
T1  - Experimental determination of dynamic fracture toughness KId in metal materials with high strength
EP  - 39
IS  - 1
SP  - 28
VL  - 2
UR  - https://hdl.handle.net/21.15107/rcub_rims_30
ER  - 

@article{
author = "Burzić, Meri and Sedmak, Stojan and Burzić, Zijah and Zrilić, Milorad and Jaković, Dragan and Momčilović, Dejan",
year = "2003",
abstract = "U ovom radu su prikazane metode za određivanje dinamičke žilavosti loma, KId Metode dinamičkog J integrala, i ekvivalenta energije su eksperimentalno potvrđene ispitivanjem čelika Č 5432 i Č 4734. Ovaj rad predstavlja doprinos u ovladavanju metodama koje definišu ponašanje materijala u dinamičkim uslovima rasta prsline. Primena ovih metoda zajedno sa ostalim metodama za određivanje parametara mehanike loma predstavlja značajan doprinos istraživanju ponašanja konstrukcijskih materijala u prisustvu prsline., In this paper the investigation of methods for determination of dynamic fracture toughness, KId. Dynamic J-integral and equivalence energy methods are experimental confirm testing of steel Č 5432 and Č 4734. This paper presented of contribution in control methods what's to define behavior of materials in condition of dynamic crack growth. Application this all methods presented very imported contribution of investigation behavior construction materials in presence of crack.",
publisher = "Visoka tehnička škola strukovnih studija, Beograd",
journal = "Tehnička dijagnostika",
title = "Eksperimentalno određivanje dinamičke žilavosti loma KId, kod metalnih materijala visoke čvrstoće, Experimental determination of dynamic fracture toughness KId in metal materials with high strength",
pages = "39-28",
number = "1",
volume = "2",
url = "https://hdl.handle.net/21.15107/rcub_rims_30"
}

Burzić, M., Sedmak, S., Burzić, Z., Zrilić, M., Jaković, D.,& Momčilović, D.. (2003). Eksperimentalno određivanje dinamičke žilavosti loma KId, kod metalnih materijala visoke čvrstoće. in Tehnička dijagnostika
Visoka tehnička škola strukovnih studija, Beograd., 2(1), 28-39.
https://hdl.handle.net/21.15107/rcub_rims_30

Burzić M, Sedmak S, Burzić Z, Zrilić M, Jaković D, Momčilović D. Eksperimentalno određivanje dinamičke žilavosti loma KId, kod metalnih materijala visoke čvrstoće. in Tehnička dijagnostika. 2003;2(1):28-39.
https://hdl.handle.net/21.15107/rcub_rims_30 .

Burzić, Meri, Sedmak, Stojan, Burzić, Zijah, Zrilić, Milorad, Jaković, Dragan, Momčilović, Dejan, "Eksperimentalno određivanje dinamičke žilavosti loma KId, kod metalnih materijala visoke čvrstoće" in Tehnička dijagnostika, 2, no. 1 (2003):28-39,
https://hdl.handle.net/21.15107/rcub_rims_30 .

TY  - JOUR
AU  - Burzić, Meri
AU  - Sedmak, Stojan
AU  - Burzić, Zijah
AU  - Jaković, Dragan
AU  - Momčilović, Dejan
PY  - 2002
UR  - http://rims.institutims.rs/handle/123456789/28
AB  - Analiziran je uticaj sadržaja Mg u matrici i zapreminskog udela SiC čestica u metal matričnom kompozitu (MMC) na udarnu žilavost. Livena AlMg legura, sa 3%, 5% i 7% sadržaja Mg korišćena je kao metal matrice. Primenjen je sadržaj ojačavaća od 2%, 5% i 10%, sa prosečnom veličinom čestica od 30 µm. Kompozit je dobijen metodom vrtložnog livenja. Energija udara metal matričnog kompozita sa AlMg matricom smanjuje se sa porastom sadržaja SiC i smanjenjem sadržaja Mg. Najveća ukupna energija je nađena u MMC AlMg7 sa 2% SiC (14,7-17,5 J), a najmanja u MMC AlMg3 sa 10% SiC (3,7-4,1 J). Vrednosti za metal matrični kompozit su manje od vrednosti za odgovarajuću leguru za 40 do 50%.
AB  - The effect of Mg content in matrix and volume entail of SiC particles in metal matrix composite (MMC) on impact toughness is analyzed. Cast AlMg alloy, with 3%, 5% and 7% Mg content is used as metal matrix. Reinforcement content of 2%, 5% and 10%, with an average particle size of 30 µm, had been applied. Composite is obtained by whirlpool casting method. The impact energy of metal matrix composite with AlMg matrix decreases with increasing SiC content and with decreasing Mg content. The highest total energy is found in MMC AlMg7 with 2% SiC (14.7-17.5 J), and the lowest one in MMC AlMg3 with 10% SiC (3.7-4.1 J). The values for metal matrix composite are bellow that of corresponding alloy for 40 to 50% .
PB  - Institut za ispitivanje materijala, Beograd
T2  - Integritet i vek konstrukcija
T1  - Uticaj sadržaja ojačavača na udarnu žilavost livenog Al-SiCp metal matričnog kompozita
T1  - The effect of reinforcement content on impact toughness of cast Al-SiCP metal matrix composite
EP  - 14
IS  - 1-2
SP  - 11
VL  - 2
UR  - https://hdl.handle.net/21.15107/rcub_rims_28
ER  - 

@article{
author = "Burzić, Meri and Sedmak, Stojan and Burzić, Zijah and Jaković, Dragan and Momčilović, Dejan",
year = "2002",
abstract = "Analiziran je uticaj sadržaja Mg u matrici i zapreminskog udela SiC čestica u metal matričnom kompozitu (MMC) na udarnu žilavost. Livena AlMg legura, sa 3%, 5% i 7% sadržaja Mg korišćena je kao metal matrice. Primenjen je sadržaj ojačavaća od 2%, 5% i 10%, sa prosečnom veličinom čestica od 30 µm. Kompozit je dobijen metodom vrtložnog livenja. Energija udara metal matričnog kompozita sa AlMg matricom smanjuje se sa porastom sadržaja SiC i smanjenjem sadržaja Mg. Najveća ukupna energija je nađena u MMC AlMg7 sa 2% SiC (14,7-17,5 J), a najmanja u MMC AlMg3 sa 10% SiC (3,7-4,1 J). Vrednosti za metal matrični kompozit su manje od vrednosti za odgovarajuću leguru za 40 do 50%., The effect of Mg content in matrix and volume entail of SiC particles in metal matrix composite (MMC) on impact toughness is analyzed. Cast AlMg alloy, with 3%, 5% and 7% Mg content is used as metal matrix. Reinforcement content of 2%, 5% and 10%, with an average particle size of 30 µm, had been applied. Composite is obtained by whirlpool casting method. The impact energy of metal matrix composite with AlMg matrix decreases with increasing SiC content and with decreasing Mg content. The highest total energy is found in MMC AlMg7 with 2% SiC (14.7-17.5 J), and the lowest one in MMC AlMg3 with 10% SiC (3.7-4.1 J). The values for metal matrix composite are bellow that of corresponding alloy for 40 to 50% .",
publisher = "Institut za ispitivanje materijala, Beograd",
journal = "Integritet i vek konstrukcija",
title = "Uticaj sadržaja ojačavača na udarnu žilavost livenog Al-SiCp metal matričnog kompozita, The effect of reinforcement content on impact toughness of cast Al-SiCP metal matrix composite",
pages = "14-11",
number = "1-2",
volume = "2",
url = "https://hdl.handle.net/21.15107/rcub_rims_28"
}

Burzić, M., Sedmak, S., Burzić, Z., Jaković, D.,& Momčilović, D.. (2002). Uticaj sadržaja ojačavača na udarnu žilavost livenog Al-SiCp metal matričnog kompozita. in Integritet i vek konstrukcija
Institut za ispitivanje materijala, Beograd., 2(1-2), 11-14.
https://hdl.handle.net/21.15107/rcub_rims_28

Burzić M, Sedmak S, Burzić Z, Jaković D, Momčilović D. Uticaj sadržaja ojačavača na udarnu žilavost livenog Al-SiCp metal matričnog kompozita. in Integritet i vek konstrukcija. 2002;2(1-2):11-14.
https://hdl.handle.net/21.15107/rcub_rims_28 .

Burzić, Meri, Sedmak, Stojan, Burzić, Zijah, Jaković, Dragan, Momčilović, Dejan, "Uticaj sadržaja ojačavača na udarnu žilavost livenog Al-SiCp metal matričnog kompozita" in Integritet i vek konstrukcija, 2, no. 1-2 (2002):11-14,
https://hdl.handle.net/21.15107/rcub_rims_28 .

TY  - JOUR
AU  - Burzić, Meri
AU  - Sedmak, Stojan
AU  - Zrilić, Milorad
AU  - Burzić, Zijah
AU  - Jaković, Dragan
AU  - Momčilović, Dejan
PY  - 2002
UR  - http://rims.institutims.rs/handle/123456789/27
AB  - Uticaj orijentacije ugljeničnih vlakana u kompozitu sa epoksi matricom na udarnu žilavost i na žilavost loma je eksperimentalno analiziran ispitivanjem Šarpi epruveta sa V zarezom i zarezanih epruveta modifikovanog CT oblika (sa oštrim vrhom zareza koji zamenjuje zamornu prslinu). Epruvete su proizvedene od uzoraka sa orijentacijom vlakana [±45]16s, [0/90]16s, kao i sa kombinovanim sastavom [02/90/±45/90/02]4s. Epruvete sa V zarezom su ispitivane na instrumentiranoj Šarpi mašini, čime je omogućeno razdvajanje energija nastanka i rasta prsline. Faktor intenziteta napona Kc je izabran kao parametar loma. Ukupne vrednosti udarne žilavosti su pokazale da [0/90]16s, kao što je očekivano, daje najveću otpornost na udar, ali su i vrednosti za [02/90/±45/90/02]4s bile zadovoljavajuće, sa pogodnim odnosom energije širenja i energije rasta prsline. Ispitivanje modifikovane CT epruvete je dalo slične i zadovoljavajuće rezultate za faktor intenziteta napona za dva uzorka ([0/90]16s i [02/90/±45/90/02]4s), dok je za treći [±45]16s, ova vrednost niža za oko 20%. Imajući na umu druge prednosti orijentacije [02/90/±45/90/02]4s, ona se može preporučiti kao najbolja uprkos nešto nižoj udarnoj energiji.
AB  - The effect of carbon fibers orientation in a composite with epoxy matrix on the impact and fracture toughness is experimentally analyzed by testing of Charpy type V notched specimens and notched specimens of modified CT form (with sharp notch tip as replacement for fatigue pre-crack). Specimens were produced from samples with carbon fiber orientation [±45]16s, [0/90]16s, and also with combined composition [02/90-/±45/90/-02]4s. Specimens with V notch have been tested on instrumented Charpy machine, enabling to separate crack initiation and propagation energies. Stress intensity factor Kc had been selected as fracture parameter. Total impact toughness values have shown that highest impact resistance belongs to [0/90]16s, as expected, but the values for [02/90/±45/90/02]4s are also satisfactory, with convenient ratio of crack propagation to crack initiation energies. Modified CT specimen testing have shown close and satisfactory results for stress intensity factor of two samples ([0/90]16s and [02/90/±45/90/02]4s), and for third sample [±45]16s this value is about 20% lower. Having in mind other benefits with [02/90/±45/90/0-2]4s, it can be recommended as superior in spite of somewhat lower impact energy.
PB  - Institut za ispitivanje materijala, Beograd
T2  - Integritet i vek konstrukcija
T1  - Uticaj orijentacije vlakana na udarnu žilavost i osobine loma kompozita ugljenična vlakna - epoksi smola
T1  - The effect of fiber orientation on impact toughness and fracture properties of carbon fiber-epoxy composite
EP  - 19
IS  - 1-2
SP  - 15
VL  - 2
UR  - https://hdl.handle.net/21.15107/rcub_rims_27
ER  - 

@article{
author = "Burzić, Meri and Sedmak, Stojan and Zrilić, Milorad and Burzić, Zijah and Jaković, Dragan and Momčilović, Dejan",
year = "2002",
abstract = "Uticaj orijentacije ugljeničnih vlakana u kompozitu sa epoksi matricom na udarnu žilavost i na žilavost loma je eksperimentalno analiziran ispitivanjem Šarpi epruveta sa V zarezom i zarezanih epruveta modifikovanog CT oblika (sa oštrim vrhom zareza koji zamenjuje zamornu prslinu). Epruvete su proizvedene od uzoraka sa orijentacijom vlakana [±45]16s, [0/90]16s, kao i sa kombinovanim sastavom [02/90/±45/90/02]4s. Epruvete sa V zarezom su ispitivane na instrumentiranoj Šarpi mašini, čime je omogućeno razdvajanje energija nastanka i rasta prsline. Faktor intenziteta napona Kc je izabran kao parametar loma. Ukupne vrednosti udarne žilavosti su pokazale da [0/90]16s, kao što je očekivano, daje najveću otpornost na udar, ali su i vrednosti za [02/90/±45/90/02]4s bile zadovoljavajuće, sa pogodnim odnosom energije širenja i energije rasta prsline. Ispitivanje modifikovane CT epruvete je dalo slične i zadovoljavajuće rezultate za faktor intenziteta napona za dva uzorka ([0/90]16s i [02/90/±45/90/02]4s), dok je za treći [±45]16s, ova vrednost niža za oko 20%. Imajući na umu druge prednosti orijentacije [02/90/±45/90/02]4s, ona se može preporučiti kao najbolja uprkos nešto nižoj udarnoj energiji., The effect of carbon fibers orientation in a composite with epoxy matrix on the impact and fracture toughness is experimentally analyzed by testing of Charpy type V notched specimens and notched specimens of modified CT form (with sharp notch tip as replacement for fatigue pre-crack). Specimens were produced from samples with carbon fiber orientation [±45]16s, [0/90]16s, and also with combined composition [02/90-/±45/90/-02]4s. Specimens with V notch have been tested on instrumented Charpy machine, enabling to separate crack initiation and propagation energies. Stress intensity factor Kc had been selected as fracture parameter. Total impact toughness values have shown that highest impact resistance belongs to [0/90]16s, as expected, but the values for [02/90/±45/90/02]4s are also satisfactory, with convenient ratio of crack propagation to crack initiation energies. Modified CT specimen testing have shown close and satisfactory results for stress intensity factor of two samples ([0/90]16s and [02/90/±45/90/02]4s), and for third sample [±45]16s this value is about 20% lower. Having in mind other benefits with [02/90/±45/90/0-2]4s, it can be recommended as superior in spite of somewhat lower impact energy.",
publisher = "Institut za ispitivanje materijala, Beograd",
journal = "Integritet i vek konstrukcija",
title = "Uticaj orijentacije vlakana na udarnu žilavost i osobine loma kompozita ugljenična vlakna - epoksi smola, The effect of fiber orientation on impact toughness and fracture properties of carbon fiber-epoxy composite",
pages = "19-15",
number = "1-2",
volume = "2",
url = "https://hdl.handle.net/21.15107/rcub_rims_27"
}

Burzić, M., Sedmak, S., Zrilić, M., Burzić, Z., Jaković, D.,& Momčilović, D.. (2002). Uticaj orijentacije vlakana na udarnu žilavost i osobine loma kompozita ugljenična vlakna - epoksi smola. in Integritet i vek konstrukcija
Institut za ispitivanje materijala, Beograd., 2(1-2), 15-19.
https://hdl.handle.net/21.15107/rcub_rims_27

Burzić M, Sedmak S, Zrilić M, Burzić Z, Jaković D, Momčilović D. Uticaj orijentacije vlakana na udarnu žilavost i osobine loma kompozita ugljenična vlakna - epoksi smola. in Integritet i vek konstrukcija. 2002;2(1-2):15-19.
https://hdl.handle.net/21.15107/rcub_rims_27 .

Burzić, Meri, Sedmak, Stojan, Zrilić, Milorad, Burzić, Zijah, Jaković, Dragan, Momčilović, Dejan, "Uticaj orijentacije vlakana na udarnu žilavost i osobine loma kompozita ugljenična vlakna - epoksi smola" in Integritet i vek konstrukcija, 2, no. 1-2 (2002):15-19,
https://hdl.handle.net/21.15107/rcub_rims_27 .

TY  - CHAP
AU  - Sedmak, Aleksandar
AU  - Burzić, Zijah
AU  - Aleksić, Vujadin
PY  - 2000
UR  - http://rims.institutims.rs/handle/123456789/670
PB  - Tehnološko-metalurški fakultet, Beograd
PB  - Institut GOŠA, Smederevska Palanka
PB  - Jugoslovenski savez za zavarivanje, Beograd
T2  - Eksperimentalne i numeričke metode mehanike loma u oceni integriteta konstrukcija
T1  - Inženjerske metode proračuna parametara mehanike loma i zavarenih spojeva
UR  - https://hdl.handle.net/21.15107/rcub_rims_670
ER  - 

@inbook{
author = "Sedmak, Aleksandar and Burzić, Zijah and Aleksić, Vujadin",
year = "2000",
publisher = "Tehnološko-metalurški fakultet, Beograd, Institut GOŠA, Smederevska Palanka, Jugoslovenski savez za zavarivanje, Beograd",
journal = "Eksperimentalne i numeričke metode mehanike loma u oceni integriteta konstrukcija",
booktitle = "Inženjerske metode proračuna parametara mehanike loma i zavarenih spojeva",
url = "https://hdl.handle.net/21.15107/rcub_rims_670"
}

Sedmak, A., Burzić, Z.,& Aleksić, V.. (2000). Inženjerske metode proračuna parametara mehanike loma i zavarenih spojeva. in Eksperimentalne i numeričke metode mehanike loma u oceni integriteta konstrukcija
Tehnološko-metalurški fakultet, Beograd..
https://hdl.handle.net/21.15107/rcub_rims_670

Sedmak A, Burzić Z, Aleksić V. Inženjerske metode proračuna parametara mehanike loma i zavarenih spojeva. in Eksperimentalne i numeričke metode mehanike loma u oceni integriteta konstrukcija. 2000;.
https://hdl.handle.net/21.15107/rcub_rims_670 .

Sedmak, Aleksandar, Burzić, Zijah, Aleksić, Vujadin, "Inženjerske metode proračuna parametara mehanike loma i zavarenih spojeva" in Eksperimentalne i numeričke metode mehanike loma u oceni integriteta konstrukcija (2000),
https://hdl.handle.net/21.15107/rcub_rims_670 .