Zero- to Three-Dimensional Nanostructures for Application in Electronics and Renewable Energy Sources: Synthesis, Characterization and Processing

Link to this page

info:eu-repo/grantAgreement/MESTD/Integrated and Interdisciplinary Research (IIR or III)/45007/RS//

Zero- to Three-Dimensional Nanostructures for Application in Electronics and Renewable Energy Sources: Synthesis, Characterization and Processing (en)
0-3D наноструктуре за примену у електроници и обновљивим изворима енергије: синтеза, карактеризација и процесирање (sr)
0-3D nanostrukture za primenu u elektronici i obnovljivim izvorima energije: sinteza, karakterizacija i procesiranje (sr_RS)
Authors

Publications

Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles - Principal Component Analysis

Vasić, Milica; Pezo, Lato; Zdravković, Jelena; Vrebalov, Marija; Radojević, Zagorka

(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)

TY  - JOUR
AU  - Vasić, Milica
AU  - Pezo, Lato
AU  - Zdravković, Jelena
AU  - Vrebalov, Marija
AU  - Radojević, Zagorka
PY  - 2018
UR  - http://rims.institutims.rs/handle/123456789/352
AB  - This research describes a study of 11 selected samples of brick clays applied in roofing tile production, by using simultaneous thermal analysis. Additionally, the laboratory-sized samples were prepared and fired (850-950 degrees C) and technological properties were determined. Mathematical analysis was applied to sum all the experimental results and help discriminate the samples by their behavior during firing. The samples, very similar according to mineralogical and chemical content, as well as granulometry tests, were successfully grouped using principal component analysis (PCA). The PCA was used to explore and easily visualize the differences between samples. The PCA performed for differential thermal analysis (DTA), differential scanning calorimetry (DSC) and differential thermogravimetry (DTG) curves clearly showed that the heat flow was mainly influenced by carbonate content and its grain size, while DTG discriminated samples according to the contents of clay minerals and carbonates. In addition, dilatometry analysis revealed which samples underwent the highest densification during the firing process. The PCA analysis of fired products properties showed that the highest correlations were between water absorption with firing shrinkage and compressive strength.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles - Principal Component Analysis
EP  - 500
IS  - 4
SP  - 487
VL  - 50
DO  - 10.2298/SOS1804487V
ER  - 
@article{
author = "Vasić, Milica and Pezo, Lato and Zdravković, Jelena and Vrebalov, Marija and Radojević, Zagorka",
year = "2018",
abstract = "This research describes a study of 11 selected samples of brick clays applied in roofing tile production, by using simultaneous thermal analysis. Additionally, the laboratory-sized samples were prepared and fired (850-950 degrees C) and technological properties were determined. Mathematical analysis was applied to sum all the experimental results and help discriminate the samples by their behavior during firing. The samples, very similar according to mineralogical and chemical content, as well as granulometry tests, were successfully grouped using principal component analysis (PCA). The PCA was used to explore and easily visualize the differences between samples. The PCA performed for differential thermal analysis (DTA), differential scanning calorimetry (DSC) and differential thermogravimetry (DTG) curves clearly showed that the heat flow was mainly influenced by carbonate content and its grain size, while DTG discriminated samples according to the contents of clay minerals and carbonates. In addition, dilatometry analysis revealed which samples underwent the highest densification during the firing process. The PCA analysis of fired products properties showed that the highest correlations were between water absorption with firing shrinkage and compressive strength.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles - Principal Component Analysis",
pages = "500-487",
number = "4",
volume = "50",
doi = "10.2298/SOS1804487V"
}
Vasić, M., Pezo, L., Zdravković, J., Vrebalov, M.,& Radojević, Z.. (2018). Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles - Principal Component Analysis. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 50(4), 487-500.
https://doi.org/10.2298/SOS1804487V
Vasić M, Pezo L, Zdravković J, Vrebalov M, Radojević Z. Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles - Principal Component Analysis. in Science of Sintering. 2018;50(4):487-500.
doi:10.2298/SOS1804487V .
Vasić, Milica, Pezo, Lato, Zdravković, Jelena, Vrebalov, Marija, Radojević, Zagorka, "Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles - Principal Component Analysis" in Science of Sintering, 50, no. 4 (2018):487-500,
https://doi.org/10.2298/SOS1804487V . .
8
6
13

Comprehensive approach to the influence of frequently used secondary raw materials on clay bricks quality using mathematical modeling (a systematic review)

Vasić, Milica; Pezo, Lato; Zdravković, Jelena; Stanković, Slavka; Radojević, Zagorka

(Elsevier Sci Ltd, Oxford, 2018)

TY  - JOUR
AU  - Vasić, Milica
AU  - Pezo, Lato
AU  - Zdravković, Jelena
AU  - Stanković, Slavka
AU  - Radojević, Zagorka
PY  - 2018
UR  - http://rims.institutims.rs/handle/123456789/351
AB  - The main idea of this research was to evaluate rice and sunflower hulls, sawdust and their ashes, as additives in clay brick production using mathematical analysis. All available papers, containing the parameters of interest, were used in the study, which consisted of total 316 cases, obtained from the literature. The major oxide content of clays and mixtures, then weight percent addition and particle size ranges of secondary raw materials, and process parameters (firing temperature, soaking time and average heating rate) were selected as inputs to mathematical models. Shaping moist was the only parameter characterizing transition state of the products analyzed as an output parameter. The other parameters described the fired product quality: linear shrinkage, bulk density, water absorption, compressive and bending strength. The main goal was to find the relationships and the main influences between raw material properties, process parameters, and the quality of the obtained products and mixtures, by using mathematical tools. Statistical and mathematical analyses were applied for prediction of final product quality. Developed artificial neural network empirical models (ANNs) give a reasonable fit to experimental data and successfully predict the most of the observed output variables, showing the good prediction capabilities (coefficient of determination varied between 0.714 and 0.998). Sensitivity analysis showed that, among all the studied parameters concerning raw materials and process parameters, the dominant influence belonged to loss on ignition.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Comprehensive approach to the influence of frequently used secondary raw materials on clay bricks quality using mathematical modeling (a systematic review)
EP  - 1276
IS  - 2
SP  - 1269
VL  - 44
DO  - 10.1016/j.ceramint.2017.10.191
ER  - 
@article{
author = "Vasić, Milica and Pezo, Lato and Zdravković, Jelena and Stanković, Slavka and Radojević, Zagorka",
year = "2018",
abstract = "The main idea of this research was to evaluate rice and sunflower hulls, sawdust and their ashes, as additives in clay brick production using mathematical analysis. All available papers, containing the parameters of interest, were used in the study, which consisted of total 316 cases, obtained from the literature. The major oxide content of clays and mixtures, then weight percent addition and particle size ranges of secondary raw materials, and process parameters (firing temperature, soaking time and average heating rate) were selected as inputs to mathematical models. Shaping moist was the only parameter characterizing transition state of the products analyzed as an output parameter. The other parameters described the fired product quality: linear shrinkage, bulk density, water absorption, compressive and bending strength. The main goal was to find the relationships and the main influences between raw material properties, process parameters, and the quality of the obtained products and mixtures, by using mathematical tools. Statistical and mathematical analyses were applied for prediction of final product quality. Developed artificial neural network empirical models (ANNs) give a reasonable fit to experimental data and successfully predict the most of the observed output variables, showing the good prediction capabilities (coefficient of determination varied between 0.714 and 0.998). Sensitivity analysis showed that, among all the studied parameters concerning raw materials and process parameters, the dominant influence belonged to loss on ignition.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Comprehensive approach to the influence of frequently used secondary raw materials on clay bricks quality using mathematical modeling (a systematic review)",
pages = "1276-1269",
number = "2",
volume = "44",
doi = "10.1016/j.ceramint.2017.10.191"
}
Vasić, M., Pezo, L., Zdravković, J., Stanković, S.,& Radojević, Z.. (2018). Comprehensive approach to the influence of frequently used secondary raw materials on clay bricks quality using mathematical modeling (a systematic review). in Ceramics International
Elsevier Sci Ltd, Oxford., 44(2), 1269-1276.
https://doi.org/10.1016/j.ceramint.2017.10.191
Vasić M, Pezo L, Zdravković J, Stanković S, Radojević Z. Comprehensive approach to the influence of frequently used secondary raw materials on clay bricks quality using mathematical modeling (a systematic review). in Ceramics International. 2018;44(2):1269-1276.
doi:10.1016/j.ceramint.2017.10.191 .
Vasić, Milica, Pezo, Lato, Zdravković, Jelena, Stanković, Slavka, Radojević, Zagorka, "Comprehensive approach to the influence of frequently used secondary raw materials on clay bricks quality using mathematical modeling (a systematic review)" in Ceramics International, 44, no. 2 (2018):1269-1276,
https://doi.org/10.1016/j.ceramint.2017.10.191 . .
7
2
8

The study of thermal behavior of montmorillonite and hydromica brick clays in predicting tunnel kiln firing curve

Vasić, Milica; Pezo, Lato; Zdravković, Jelena; Backalić, Z.; Radojević, Zagorka

(Elsevier Sci Ltd, Oxford, 2017)

TY  - JOUR
AU  - Vasić, Milica
AU  - Pezo, Lato
AU  - Zdravković, Jelena
AU  - Backalić, Z.
AU  - Radojević, Zagorka
PY  - 2017
UR  - http://rims.institutims.rs/handle/123456789/315
AB  - The aim of this study was to test montmorillonite and hydromica type of brick clays by using simultaneous thermal analysis and dilatometry in an assessment of the suitability of brick clays to produce building elements. The plasticity coefficient and drying susceptibility were determined to discover the behavior of brick clays. Fired products' characteristics were studied by performing water absorption and compressive strength tests. All the methods were employed in the construction of the firing curves in a tunnel kiln. The results could increase the degree of certainty to lead the production process towards obtaining the desired features of brick elements.
PB  - Elsevier Sci Ltd, Oxford
T2  - Construction and Building Materials
T1  - The study of thermal behavior of montmorillonite and hydromica brick clays in predicting tunnel kiln firing curve
EP  - 879
SP  - 872
VL  - 150
DO  - 10.1016/j.conbuildmat.2017.06.068
ER  - 
@article{
author = "Vasić, Milica and Pezo, Lato and Zdravković, Jelena and Backalić, Z. and Radojević, Zagorka",
year = "2017",
abstract = "The aim of this study was to test montmorillonite and hydromica type of brick clays by using simultaneous thermal analysis and dilatometry in an assessment of the suitability of brick clays to produce building elements. The plasticity coefficient and drying susceptibility were determined to discover the behavior of brick clays. Fired products' characteristics were studied by performing water absorption and compressive strength tests. All the methods were employed in the construction of the firing curves in a tunnel kiln. The results could increase the degree of certainty to lead the production process towards obtaining the desired features of brick elements.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Construction and Building Materials",
title = "The study of thermal behavior of montmorillonite and hydromica brick clays in predicting tunnel kiln firing curve",
pages = "879-872",
volume = "150",
doi = "10.1016/j.conbuildmat.2017.06.068"
}
Vasić, M., Pezo, L., Zdravković, J., Backalić, Z.,& Radojević, Z.. (2017). The study of thermal behavior of montmorillonite and hydromica brick clays in predicting tunnel kiln firing curve. in Construction and Building Materials
Elsevier Sci Ltd, Oxford., 150, 872-879.
https://doi.org/10.1016/j.conbuildmat.2017.06.068
Vasić M, Pezo L, Zdravković J, Backalić Z, Radojević Z. The study of thermal behavior of montmorillonite and hydromica brick clays in predicting tunnel kiln firing curve. in Construction and Building Materials. 2017;150:872-879.
doi:10.1016/j.conbuildmat.2017.06.068 .
Vasić, Milica, Pezo, Lato, Zdravković, Jelena, Backalić, Z., Radojević, Zagorka, "The study of thermal behavior of montmorillonite and hydromica brick clays in predicting tunnel kiln firing curve" in Construction and Building Materials, 150 (2017):872-879,
https://doi.org/10.1016/j.conbuildmat.2017.06.068 . .
22
13
22