Претраживање
Приказ резултата 21-30 од 198
Model of Probabilistic Analysis of Pile Capacity Based on the Extrapolation of Load-Settlement Curves
(Springer, New York, 2020)
This paper formulates a mathematical model using the extrapolation of load-settlement curves with a rational function for analyzing the capacity of piles obtained from the static load test (SLT). In preliminary analyses, ...
Concrete paving blocks and flags made with crushed brick as aggregate
(Construction and Building Materials, 2012)
Demolition of old buildings in urban cores has produced a large amount of waste material. Since they are mostly masonry structures the largest part of the waste material is ceramic waste. Besides that, ceramic waste is ...
Mix design and engineering properties of ultra high performance self compacting concrete
(Czech Concrete Soc-Ceska Betonarska Spolecnost Cssi, Prague 1, 2011)
The mechanical properties (compressive strength and flexural strength) were investigated under different curing conditions (standard and steam curing). Silica fumes have characteristics that make them necessary in cement ...
Influence of FSW parameters on formation quality and mechanical properties of Al 2024-T351 butt welded joints
(Elsevier, Amsterdam, 2013)
The influence of R/v ratio on joint quality in 2024-T351 aluminum alloy was studied. Specimens were subjected to friction stir welding with the rotation rates of 750, 950 and 1180 r/min and welding speed between 73 and 190 ...
Analysis of current state and integrity evaluation for the supply tank of generation unit 6 of thermal power plant Nikola Tesla ”A”, Obrenovac
(Trans Tech Publications Ltd, 2014)
Stable supply tank, with volume V = 250 m3 and operating pressure p = 1,5 MPa, of generation unit 6 at thermal power plant 'Nikola Tesla A' in Obrenovac, is designed for water-steam working fluid. It was made of steel Č ...
Investigation of the Repair Welding Technology Using Ni Base Electrode
(Trans Tech Publications Ltd, Durnten-Zurich, 2013)
Metal materials are subjected to innumerable time-dependent degradation mechanisms when operate in power, petrochemical and refinery plant. These materials are subjected to multiaxial stresses, creep, fatigue, corrosion ...
Methodology for reparation of damaged sleeves and welded shield sections of guide vanes at hydropower plant DJERDAP 1
(Trans Tech Publications Ltd, 2014)
Vertical Kaplan turbines, manufactured in Russia and with nominal power of 200 MW, have been installed in 6 hydroelectric generating units at ’Djerdap 1’. During the refurbishment of hydropower plant experimental non-destructive ...
Analytical modeling of activation procedure applied in alpha-alumina thermo-mechanical synthesis
(Elsevier Sci Ltd, Oxford, 2015)
The impact of the mechanical processing parameters on the alumina grain-size distribution affiliated characteristics and on the gamma to alpha phase transformation rate was investigated. The moderation in the alumina samples ...
Has the latest global financial crisis changed the way road public-private partnerships are funded? A comparison of Europe and Latin America
(Elsevier Sci Ltd, Oxford, 2020)
A financial/economic crisis may have an adverse effect on transport public-private partnerships (PPPs) as both traffic demand is negatively influenced, and governments are further under pressure. However, research on awarded ...
Određivanje preciznosti metoda ispitivanja mehaničkih karakteristika opekarskih proizvoda i crepova od gline uporednim ispitivanjem / Determining brick and roof tile mechanical characteristics testing accuracy: Comparative investigation
(Udruženje inženjera građevinarstva, geotehnike, arhitekture i urbanista "Izgradnja", Beograd, 2011)
U okviru standarda SRPS ISO/IEC 17025:2006 - Opšti zahtevi za kompetentnost laboratorija za ispitivanje i laboratorija za etaloniranje, pod tačkom 5.9 postoji zahtev koji se odnosi na obezbeđenje poverenja u kvalitet ...