Претраживање
Приказ резултата 1-10 од 10
Thermal and Mechanical Behavior of Composite Mortars Containing Natural Sorptive Clays and Fly Ash
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Mineral additives are extensively applied as cement replacement materials in both construction concrete and mortar. Fly ash is one of the most commonly utilized additives which improve Theological properties, as well as ...
MSV sistem za obradu signala sa neutron-gama diskriminacijom u mešovitom polju / MSV signal processing system for neutron-gamma discrimination in a mixed field
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2012)
Na osnovu principa koji su proizišli iz Kempbelove teoreme, u ovom radu je urađena analiza nekih mogućnosti Kempbelovog MSV sistema za obradu signala. MSV mod je posebno pogodan za merenja koja se sprovode u mešovitom polju ...
Novel Approach for Determination of Potentially Toxic Elements via ICP-OES in Aqueous Solutions of Building Materials with Industrial Byproduct Addition
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
New global tendencies for waste materials reusing in building materials are imposing the request for improved performances of chemical analysis methods and the improvements of matrices used. A new method for optical emission ...
Mechanical Properties and Microstructure Fractal Analysis of Refractory Bauxite Concrete
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
The surface topography analysis via fractals as a means of explanation of composite materials mechanical and microstructural characteristics has hardly been reported so far. This study proposes a method of fractal analysis ...
Experimental and numerical thermo - mechanical analysis of friction stir welding of high - strength alluminium alloy
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
This paper presents experimental and numerical analysis of the change of temperature and force in the vertical direction during the friction stir welding of high-strength aluminium alloy 2024 T3. This procedure confirmed ...
Synthesis and characterization of new refractory coatings based on talc, cordierite, zircon and mullite fillers for lost foam casting process
(Polska Akad Nauk, Polish Acad Sciences, Inst Metall & Mater Sci Pas, Warszawa, 2014)
Refractory coatings based on different refractory fillers (talc, cordierite, zircon and mullite) for application in Lost Foam casting process were investigated. Design and optimization of the coatings composition with ...
Identification of low cycle fatigue parameters of high strength low-alloy (HSLA) steel at room temperature
(Croatian Metallurgical Soc, Zagreb, 2014)
Low cycle fatigue test was performed in ambient atmosphere at room temperature. cycle loading of material, in case of High strength low-alloy steel, entails modifications of its properties and in this paper is therefore ...
Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue
(Croatian Metallurgical Soc, Zagreb, 2014)
High strength low-alloy steel under low cycle fatigue at a certain level of strain controlled achieve stabilized condition. During the fatigue loading stabilized hysteresis loop is determined, which typical cycle of ...
Cavitation damages morphology of high-strength low-alloy steel
(Faculty of Metallurgy, 2016)
This paper presents the research into behaviour of HSLA steel affected by cavitation. The parent material (PM) and simulated heat-affected zone (SHAZ) were studied. Ultrasonic vibratory cavitation test was performed in ...
Mechanical Activation as Sintering Pre-treatment of Talc for Steatite Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
The effect of vibratory mill induced mechanical activation on the change of the particle size, crystallinity and the phase transformations of the minerals present in the activated material, was studied with the purpose of ...