Pretraživanje
Prikaz rezultata 121-130 od 140
Bucket-wheel excavator gearbox failure analysis and reliability assessment
(Institute for Engineering Design and Product Development-ViennaFaculty of Mechanical Engineering University of Belgrade, 2019)
This paper presents the analysis of failure causes and reliability
assessment executed for the gearbox of the bucket-wheel excavator SRs
470.20/3 “TAKRAF” (produced by “Lauhhammer”, Germany), which is
engaged in overburden ...
Mechanical properties of welded pipes produced by high frequency welding of the steel API J55
(University of Banja Luka, Faculty of Mechanical Engineering, Banja Luka, Republika Srpska, 2019)
Selection of steel, dimensions and methods of production of welded pipes is
a segment of the design process, because it is closely related to the function of a piping
as a structural whole under predetermined conditions ...
Vulnerability of Damaged Structures: The Concept of the Scenario of Related Non-Linear Analyses
(Varna Free University “Chernorizets Hrabar”, Varna, Bulgaria, 2014)
The research presented in the paper employed the general approach in the analysis of robustness of reinforced concrete skeletal (frame) structures in the events of severe damage caused by strong earthquakes. Such damage ...
Analysis of the steam line damages
(Mašinski Fakultet Banja Luka, Republika Srpska, 2015)
The methodological approach to the analysis of damage to determine the
cause of failure and to repair the damage has been shown using the example of leakage
and damage of a steam line for live-steam in thermal power ...
Determination of polynomial depending between hardness and cooling time t8/5 of steel NIONICRAL 70 heat affected zone
(18th International Conference on New Trends in Fatigue and Fracture NT2F18, 2018)
Because of the high heating and cooling velocity values, welding procedure is an unstable process. During
welding, changes in microstructure are occurring under overheating and/or cooling conditions. In comparing to ...
Behaviour of 9% Cr steel and simulated HAZ at 600°C
(FRACT3, Chlef, Algeria, 2016)
Ispitivanja turbinskih vratila u funkciji donošenja odluke o sanaciji
(University of Zenica, Faculty of Mechanical Engineering, Bosna i Hercegovina, 2012)
Nakon preko 20 godina rada agregata na HE Đerdap II, u cilju utvrđivanja stanja turbinskih vratila
izvršena su detaljna ispitivanja metodama IBR. Na svim vratilima utvrđene su površinske prsline
različitih dužina i dubina, ...
Non - desctructive testing of pressure vessels – Application of SolidWorks
(Mašinski Fakultet Banja Luka, Republika Srpska, 2015)
This paper describes application of parametric software for drawing and
modelling on testing of pressure vessels. The used software, SolidWorks, is used to
demonstrate all phases of testing: preparation of non-destructive ...
Control of hazardous waste in the laboratory for metal testing-current problems / Kontrolisanje opasnog otpada u laboratoriji za ispitivanje metala - aktuelni problemi
(Udruženje inženjera Srbije za koroziju i zaštitu materijala, Srbija, 2013)
This paper presents a controlled process of collecting, identification, classification and labeling of waste and
hazardous materials in laboratory for testing materials of the Institute of testing materials {Institute ...
Methodological approach to recovery of damages of the steamlines in thermal power plants and heating plants / Metodološki pristup sanaciji oštećenja parovoda u termoelektranama i toplanama
(Tehnološki fakultet Zvornik, BiH, 2013)
Na primeru procurivanja i ostecenja parovoda sveze pare u termoelektranama i toplanama
prikazan je metodoloski pristup utvrdivanja uzroka otkaza i saniranja ostecenja. Dati pristup se
moze primeniti za slicne konstrukcije, ...