Претраживање
Приказ резултата 331-340 од 452
Uporedna analiza proračuna mašinskih elemenata simuliranjem kombinovanog opterećenja i odvojenim simuliranjem komponentnih opterećenja - studija slučaja / Combined load simulation vs component loads simulation in machine design: A case study
(Univerzitet u Beogradu - Mašinski fakultet, Beograd, 2014)
Na sadašnjem nivou razvoja tehnologije, u stvarnim radnim uslovima, gotovo svi mašinski elementi su opterećeni kombinovanim opterećenjima. Cilj istraživanja prikazanog u ovom radu je ukazivanje na značaj proračuna nosivosti ...
Spregnuti nelinearni problemi u analizi konačnim elementima - studija slučaja / Coupled nonlinear problems in finite element analysis: A case study
(Integritet i vek konstrukcija, Beograd, 2012)
Rad daje opis analize elastoplastičnih deformacija čeličnog cevnog apsorbera kinetičke energije sudara železničkih vozila metodom konačnih elemenata (FEM). Eksperimentalna istraživanja korišćena su kao osnova za modeliranje ...
A new methodology for prediction of high-cycle contact fatigue for spur gears
(Univerzitet u Novom Sadu - Fakultet tehničkih nauka, Novi Sad, 2012)
High-cycle contact fatigue is a localized phenomenon that occurs in highly stressed grains of the material on or under the contact region. The contact zones of tooth flanks for meshed gears are subjected to contact fatigue ...
Failure analysis of hydraulic turbine shaft
(Pergamon-Elsevier Science Ltd, Oxford, 2012)
This paper describes the analysis of major failure of 28 MW horizontal hydro turbine shaft. The analysis of load carrying capacity of critical radius and fractography analysis are presented. Special emphasize is on ...
Methodology of determination the influence of corrosion pit on decrease of hydro turbine shaft fatigue life
(Univerzitet u Novom Sadu - Fakultet tehničkih nauka, Novi Sad, 2012)
This paper describes the influence of corrosion on stress concentration factor and crack initiation at shaft flange transition section. The case study of hydraulic turbine shaft failure is used as the basis for this research. ...
Effects of operation temperature on thermal expansion and main parameters of radial ball bearings
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2015)
The research of influence of operation temperature on the thermal expansion and main parameters of radial ball bearings is presented in this paper. The main bearing parameters are identified in accordance with the increasing ...
Analysis of the nominal load effects on gear load capacity using the finite-element method
(Sage Publications Ltd, London, 2010)
This research investigates the effects of the nominal load value on load distribution of simultaneously meshing gear teeth pairs, and on the involute gear load capacity. The research results presented in this article confirm ...
Assessment of the effect of pitting corrosion on fatigue crack initiation in hydro turbine shaft
(Trans Tech Publications Ltd, 2013)
Energy efficiency is a key issue worldwide, and not confined solely to the realm of engineers. Past failures of mechanical power system components must be examined carefully in order to minimise future occurrences and ...
Sistematizacija analitičkih i numeričkih metoda proračuna stabilnosti klizišta / The systematization of analytical and numerical methods of landslide stability calculation
(Društvo za ispitivanje i istraživanje materijala i konstrukcija Srbije, Beograd, 2018)
Na osnovu analize mnogih naučnih radova, autori su dali prikaz sopstvene originalne sistematizacije analitičkih i numeričkih metoda proračuna stabilnosti klizišta, pri čemu mnoge od njih tek treba dodatno da se unaprede, ...
Thermal and Mechanical Behavior of Composite Mortars Containing Natural Sorptive Clays and Fly Ash
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Mineral additives are extensively applied as cement replacement materials in both construction concrete and mortar. Fly ash is one of the most commonly utilized additives which improve Theological properties, as well as ...