Претраживање
Приказ резултата 61-70 од 266
Probabilistic Analysis of Bearing Capacity of Piles with Variable Parameters of CPT Test and Calculation According to the EN 1997-1: 2004
(GNP 2016, Civil Engineering – Science and Practice, International Conference, Žabljak, Montenegro, 2016)
A probabilistic concept for determining pile bearing capacity is presented, taking into account the variability of CPT test parameters and methodology of calculation according to the requirements of Eurocode 7 (EN 1997-1: ...
Need to Improve the Natural Aggregate Resources Supply in the City of Belgrade (Serbia)
(Berg Fac Technical Univ Kosice, Kosice, 2016)
The City of Belgrade is the largest market for aggregates in Serbia but the production of natural aggregates is rather small, around five percent of total consumption. This reflects the geology of the City of Belgrade ...
Predviđanje optimalnih parametara interventnog reparaturnog zavarivanja čelika 13CrMo4-5 analitičkim metodama / Optimal parameters estimation by the analytical methods for the emergency repair welding of the 13CrMo4-5 steel
(DUZS - Društvo za unapređivanje zavarivanja u Srbiji, Beograd, 2010)
Već dugi niz godina se čelik 13CrMo4-5 (~Č7400) primenjuje za izradu delova termoenergetskih postrojenja kao što su elementi kotlova i cevi. Ovaj čelik pripada grupi uslovno zavarljivih čelika, koji mogu uspešno da se ...
Activated carbons obtained by pyrolyzing of resorcinol formaldehyde gels
(University of East Sarajevo, Faculty of Technology, 2010)
Activated carbon is used in different industrial domains due to highly developed specific surface area and its specific chemistry. Properties of activated carbons obtained by pyrolyzing formaldehyde gels are presented in ...
Determination of the apparent porosity level of refractory concrete during a sintering process using an ultrasonic pulse velocity technique and image analysis
(Savez hemijskih inženjera, Beograd, 2010)
Concrete which undergoes a thermal treatment before (pre-casted concrete blocks) and during (concrete embedded in-situ) its life-service can be applied in plants operating at high temperature and as thermal insulation. ...
Behaviour of nionikral-70 in low-cycle fatigue
(Institut za ispitivanje materijala, Beograd, 2017)
Experimental research on the behaviour of high-strength low-alloy steel ( HSLA)exposed to low-cycle fatigue (LCF) with controlled and fully reversible strain (Delta epsilon/2 = const, R epsilon =epsilon(min)/epsilon(max) ...
Experimental study on the stresses at the i-beam end-plate moment connection
(Institut za ispitivanje materijala, Beograd, 2019)
The paper deals with experimental study of the stresses at the bolted end-plate moment connection. The design parameters are adopted to include prying effects in joint. A stress level is obtained in the elements where the ...
Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue
(Croatian Metallurgical Soc, Zagreb, 2014)
High strength low-alloy steel under low cycle fatigue at a certain level of strain controlled achieve stabilized condition. During the fatigue loading stabilized hysteresis loop is determined, which typical cycle of ...
Prompt system redesign: Shifting to open source technology to satisfy user requirements
(ComSIS Consortium, 2010)
The paper describes a redesign project undertaken in a short period to adapt a software system to user needs. Additional goals of the project included a shift to Open Source software and the selection of technology to ...
Microstructural analysis as the indicator for suitability of weld repairing of the heat resistant Cr - Ni steel
(Consejo Superior Investigaciones Cientificas-Csic, Madrid, 2010)
Metallurgical evaluation was performed on a fractured column tube of the reformer furnace in an ammonia plant. The tubes were manufactured from centrifugally cast heat resistant steel HK 40. Optical and scanning electron ...